280m3/H Petrochemical Pharmaceutical Chemical Water Liquid Ring 2BV6121-0K Nash Vacuum Pump System

2BV2, 2BV5, are suitable for pumping dry and wet gases, mainly non-flammable, non-corrosive atmospheres and atmospheric/vapor mixtures. 2BV6 is suitable for pumping flammable and explosive gases and for flammable and explosive working environments. The working fluid is usually water. Stainless steel pumps are suitable for applications with more demanding corrosion and sanitary requirements. 2BV vacuum pumps are used in the rough vacuum range and the ultimate vacuum is determined by the saturated vapor pressure of the working fluid.
Ultimate vacuum
The ultimate vacuum depends on the working temperature and the type of working fluid used. Please note the following points: a pump without cavitation protection, suction pressure must not be less than 80 mbar, this is to avoid the water temperature of 15 ºC, the temperature of the pumped dry air at 20 ºC in the pump caused by cavitation, the higher the temperature, depending on the working fluid saturated vapor pressure, the minimum suction pressure allowed will also be higher. The higher the temperature, the lower the suction capacity. Note: 2BV vacuum pumps operating for a long time under the minimum allowable suction pressure will cause damage to the pump.
Maximum exhaust pressure
The maximum allowable exhaust pressure is 1200 mbar for 2BV2 vacuum pumps and 1300 mbar for 2BV5 and 2BV6 vacuum pumps when using working fluid according to the flow rate in the table.
Pumped gases or vapors
The pumped gas or gas/vapor mixture is not allowed to contain solid particles, but a small amount of suspended matter or liquid is allowed. Table 2 shows the maximum amount of water allowed to be drawn in from the suction flange. When pumping hot gases or steam above 80°C, it is recommended to use 2 times the standard flow rate of working fluid

2BV series products have the feature of strong suction capacity under high vacuum, which is the ideal vacuum pump for paper, chemical and pharmaceutical industries.

 1. Direct coupling connection to space and easy to install.
2. High quality mechanical seal as standard configuration, leakage-free and maintenance-free.
3. Equipped with Y2 series motor with protection grade IP54.
4. Smooth running, noise can be as low as 62 decibels.
5. Uniform corrosion-resistant design, aluminum bronze impeller is used to improve the corrosion resistance of the pump, stainless steel impeller is optional and can be used for the harsh application environment.
6. The unique design of the discharge port can protect the pump from the over-pressure to ensure the best efficiency.

Note: 2BV6060~2BV6161 is Anti- Explosion design.

Q: What information should I offer for an inquiry?
A: You can inquire based on the model directly, but it is always recommended that you contact us so that we can help you to check if the pump is the most appropriate for your application.

Q: Can you make a customized vacuum pump?
A: Yes, we can do some special designs to meet customer applications. Such as customized sealing systems, speical surface treatment can be applied for roots vacuum pump and screw vacuum pump. Please contact us if you have special requirements. 

Q: I have problems with our vacuum pumps or vacuum systems, can you offer some help?
A: We have application and design engineers with more than 30 years of experience in vacuum applications in different industries and help a lot of customers resolve their problems, such as leakage issues, energy-saving solutions, more environment-friendly vacuum systems, etc. Please contact us and we'll be very happy if we can offer any help to your vacuum system.

Q: Can you design and make customized vacuum systems?
A: Yes, we are good for this.

Q: What is your MOQ?
A: 1 piece or 1 set.

Q: How about your delivery time?
A: 5-10 working days for the standard vacuum pump if the quantity is below 20 pieces, 20-30 working days for the conventional vacuum system with less than 5 sets. For more quantity or special requirements, please contact us to check the lead time.

Q: What are your payment terms?
A: By T/T, 50% advance payment/deposit and 50% paid before shipment.

Q: How about the warranty?
A: We offer 1-year warranty (except for the wearing parts).

Q: How about the service?
A: We offer remote video technical support. We can send the service engineer to the site for some special requirements.